|
|||||||
 |
|
|
LinkBack | Thread Tools | Search this Thread | Rate Thread | Display Modes |
07-13-2007, 04:58 PM
|
#1 |
|
Member (6 bit)
Join Date: Jun 2007
Posts: 62
|
2 More Questions and then Finished! TY!
NEVERMIND! I am SO sorry, flanzig1, and THANKFUL! Because I DID forget to plug in the 4-pin, it now works outside the case. Boot signal is there.
But now... I have more questions: 1.) I have two CHA_FANs(chassis fans), and my mobo has 1 3-pin connector for 1 CHA_FAN... though, they do come with adapters for those darn 2x4-pin connector things like the PSU has... but, I don't know... do I connect the PSU and the CHA_FAN connectors? 2.) What do I do after it starts up? Does it go to BIOS? Do I install the OS(Win XP) at the start? What do I do? :P 3.) Thank you. Setup: http://www.newegg.com/Product/Produc...82E16817103024 http://www.newegg.com/Product/Produc...82E16814130056 http://www.newegg.com/Product/Produc...82E16822148230 http://www.newegg.com/Product/Produc...82E16813131041 http://www.newegg.com/Product/Produc...82E16819115015 http://www.newegg.com/Product/Produc...82E16832116056 http://www.newegg.com/Product/Produc...82E16811119068 http://www.newegg.com/Product/Produc...82E16820145098 Last edited by Fo1k-E; 07-13-2007 at 08:28 PM. Reason: Answered the boot signal question(ty), and don't want to start a new thread. Ty. |
|
|
|
07-13-2007, 05:54 PM
|
#2 |
|
Wrench Bender
Join Date: Dec 2002
Location: Plymouth,MN
Posts: 5,961
|
Make sure that the 24 pin AND the 4 pin connectors from the PSU are connected to the motherboard. Your video card uses the 6 pin PCI-E connector from the PSU.
__________________
"When sliding down the banister of life; look out for splinters pointing up."
|
|
|
|
|
07-13-2007, 07:06 PM
|
#3 |
|
Member (6 bit)
Join Date: Jun 2007
Posts: 62
|
NEVERMIND! I am SO sorry, flanzig1, and THANKFUL! Because I DID forget to plug in the 4-pin, it now works outside the case. Boot signal is there.
But now... I have more questions: 1.) I have two CHA_FANs(chassis fans), and my mobo has 1 3-pin connector for 1 CHA_FAN... though, they do come with adapters for those darn 2x4-pin connector things like the PSU has... but, I don't know... do I connect the PSU and the CHA_FAN connectors? 2.) What do I do after it starts up? Does it go to BIOS? Do I install the OS(Win XP) at the start? What do I do? :P 3.) Thank you. Last edited by Fo1k-E; 07-13-2007 at 08:27 PM. |
|
|
|
|
07-13-2007, 08:25 PM
|
#4 |
|
Member (6 bit)
Join Date: Jun 2007
Posts: 62
|
NEVERMIND! I am SO sorry, flanzig1, and THANKFUL! Because I DID forget to plug in the 4-pin, it now works outside the case. Boot signal is there.
But now... I have more questions: 1.) I have two CHA_FANs(chassis fans), and my mobo has 1 3-pin connector for 1 CHA_FAN... though, they do come with adapters for those darn 2x4-pin connector things like the PSU has... but, I don't know... do I connect the PSU and the CHA_FAN connectors? 2.) What do I do after it starts up? Does it go to BIOS? Do I install the OS(Win XP) at the start? What do I do? :P 3.) Thank you. |
|
|
|
|
| Bookmarks |
| Thread Tools | Search this Thread |
| Display Modes | Rate This Thread |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| boot disk-how to | acuariano | Windows Legacy Support (XP and earlier) | 11 | 01-02-2007 11:36 AM |
| Boot from Atapi CD-Rom Failure | EDB | Computer Hardware | 9 | 02-25-2005 11:12 PM |
| No video signal, can't boot up | CUREYOURHUNGER | Home Theater, Audio, and Video | 1 | 01-26-2005 05:08 PM |
| Dual Boot Windows 2000 & Mandrake Boot Manager Problem | GfW | Linux OS and Software Assistance | 4 | 07-22-2003 07:06 AM |
| Unusual boot.ini add boot device request. | reboot | Windows Legacy Support (XP and earlier) | 3 | 04-24-2003 05:40 PM |
Linear Mode
