|
|||||||
 |
|
|
LinkBack | Thread Tools | Search this Thread | Rate Thread | Display Modes |
08-05-2008, 01:57 AM
|
#1 |
|
Member (6 bit)
Join Date: Mar 2008
Posts: 55
|
USB Device Over Current Status Detected
"USB Device Over Current Status Detected. pc will shut down in 15 seconds."
got this message along with "no keyboard detected" after building my pc. now after trying a few things i googled like taking out usb devices and a stick of ram i re- installed the ram after no success and theres no power what-so-ever. to be honest i installed the ram in the wrong slot the second time and then switched it and still nothing. any suggestions??? thanks. |
|
|
|
08-05-2008, 09:48 AM
|
#2 |
|
I like me
Join Date: May 2007
Location: Tejas
Posts: 7,332
|
Can you please list make and model of all parts.
Do you have any peripherals plugged in? Have you installed the motherboard drivers? Have you enabled usb support in the bios?
__________________
It's coming....just you wait. |
|
|
|
|
08-05-2008, 06:27 PM
|
#3 |
|
Member (6 bit)
Join Date: Mar 2008
Posts: 55
|
here is a list of my stuff
please help with new build... other than ocz 780 gamextreme psu and 750g hd. i also have Hauppauge WinTV-HVR 1800 MCE Kit 1128 PCI-Express x1 Interface everything hooked up. i tried unplugging usb devices. i'm a first timer so i think i hooked everything up correctly. as best i could with the directions i could find. i can't load anything because it also says "no keyboard detected. it just won't let me do anything.. thanks... |
|
|
|
|
08-05-2008, 06:41 PM
|
#4 |
|
I like me
Join Date: May 2007
Location: Tejas
Posts: 7,332
|
Take out the wintv card.
Is your keyboard a usb keyboard? If so, try a ps/2 one. No peripherals, no drives other then the main hard drive and cd drive. |
|
|
|
|
08-05-2008, 09:37 PM
|
#5 |
|
Member (6 bit)
Join Date: Mar 2008
Posts: 55
|
took out wincard unplugged usb's and took mobo out of case. had vid card, hdd, both op drives connected. got to bios with no apparent errors and the keyboard worked fine. got to bios. installed mobo in case with same internals hooked up and new error occured. said something like"fatal error occured"
|
|
|
|
|
08-05-2008, 09:45 PM
|
#6 |
|
I like me
Join Date: May 2007
Location: Tejas
Posts: 7,332
|
Either there is a short, or the case door isn't on, and you have a mb that has a case intrusion error or something.
Did you install the standoffs in the case before the motherboard? Double check all the connections. |
|
|
|
|
08-05-2008, 09:57 PM
|
#7 |
|
Member (6 bit)
Join Date: Mar 2008
Posts: 55
|
i left some standoffs off the case this time in case the mobo was geting grounded on the tower. i put the standoffs on first. just the 4 corners. boths side of the tower were left off since the beginning. should i try using masking tape as like washers in between the standoffs, the screws and the board??? should i tighten the sliding wall the mobo is on to the rear of the case like as if it were all installed and tightened up???
thanks shadow... |
|
|
|
|
08-06-2008, 08:35 PM
|
#8 |
|
Member (6 bit)
Join Date: Mar 2008
Posts: 55
|
okay, not getting error message no more, but it's still saying no keyboard detected. i'm using the old fashion plug in keyboard....anyone, lol..
|
|
|
|
|
08-06-2008, 08:37 PM
|
#9 |
|
Member (6 bit)
Join Date: Mar 2008
Posts: 55
|
oh, but when i plug in the keyboard while pc is on the keyboard blinks so it's connected..
|
|
|
|
|
08-06-2008, 08:39 PM
|
#10 |
|
I like me
Join Date: May 2007
Location: Tejas
Posts: 7,332
|
Usb or ps/2 keyboard?
Does it work after windows loads? |
|
|
|
|
08-06-2008, 08:46 PM
|
#11 |
|
Member (6 bit)
Join Date: Mar 2008
Posts: 55
|
i guess it's the ps2. it's the one with the color coded circular plug and it doesn't work at any time. i haven't done anything to the pc yet like loading software including windows vista or the cd that cam with the mobo. can't do anything without a keyboard detected....
|
|
|
|
|
08-06-2008, 08:52 PM
|
#12 |
|
I like me
Join Date: May 2007
Location: Tejas
Posts: 7,332
|
I would try a different keyboard.
|
|
|
|
|
08-06-2008, 08:57 PM
|
#13 |
|
Member (6 bit)
Join Date: Mar 2008
Posts: 55
|
for some reason it worked before, when i had everything hooked up outside of the tower so i don't think it's the keyboard. plus i don't have another other than a usb one...lol.
|
|
|
|
|
08-06-2008, 08:59 PM
|
#14 |
|
I like me
Join Date: May 2007
Location: Tejas
Posts: 7,332
|
Can't hurt to try the usb one.
Not sure why the ps/2 one wouldn't work though. |
|
|
|
|
08-06-2008, 09:05 PM
|
#15 |
|
Member (6 bit)
Join Date: Mar 2008
Posts: 55
|
i'll give it a try. thanks shadow...
|
|
|
|
|
08-06-2008, 09:05 PM
|
#16 |
|
I like me
Join Date: May 2007
Location: Tejas
Posts: 7,332
|
just let us know how it goes.
|
|
|
|
|
08-06-2008, 10:49 PM
|
#17 |
|
Member (6 bit)
Join Date: Mar 2008
Posts: 55
|
asus said "sounds like your i/o chip is dead". wants me to send it back to newegg. thanks for all your help shadow. just wish my first build would've been smooth, lol...
|
|
|
|
|
08-06-2008, 11:06 PM
|
#18 |
|
I like me
Join Date: May 2007
Location: Tejas
Posts: 7,332
|
Interesting since it was fine before.
At least newegg has a good rma service. Let us know what happens when you get a new one. And if it wen completely smooth, would you have learned this much??? huh??? lol |
|
|
|
|
08-12-2008, 07:18 PM
|
#19 |
|
Member (6 bit)
Join Date: Mar 2008
Posts: 55
|
got new mobo. loaded great, but with one error. my mouse only moves left and right (ps/2). once i got that far i could use the wireless through the usb without problems. also, being a newbie and all (thanks for the great site and helpfull folks around here), i'm not sure what i got to do to get internet, though. i have at&t high speed hooked to the other pc's and using same jack as the pc that just killed it's self so i have connection. any idea where i go from here??? do i need to do something to the pc or do i need to call at&t to help me hook up ip addresses or something??? thanks.
|
|
|
|
|
08-12-2008, 07:21 PM
|
#20 |
|
I like me
Join Date: May 2007
Location: Tejas
Posts: 7,332
|
Got everything working good now?
So this new computer isn't comnnected to the internet? But your old one is? And you want to connect both? |
|
|
|
|
08-12-2008, 07:27 PM
|
#21 |
|
Member (6 bit)
Join Date: Mar 2008
Posts: 55
|
yes, pc working good except the mouse moving from left to right only.
no, my old one was connected. it's dead. i want to connect new one where old one was. there are other pc's in the house running of router so connection is definately still up and running. the new pc will be plugged in through usb connection. the new one says i need updated drivers when i try and connect. curious if i need to do anything to the new pc to prep for internet access??? |
|
|
|
|
08-12-2008, 07:34 PM
|
#22 |
|
I like me
Join Date: May 2007
Location: Tejas
Posts: 7,332
|
If you have a router, you should just be able to connect the computer to the router with cat 5 cable.
As long as you installed the motherboard drivers (which includes the network driver), then you shouldn't have to do anything else. |
|
|
|
|
08-12-2008, 08:46 PM
|
#23 |
|
Member (6 bit)
Join Date: Mar 2008
Posts: 55
|
installed mobo drivers and am now browsing the web. thanks shawdow for all your help. time to give this puppy a test drive, lol. tommorow i get my aftermarket cpu fan and then i can see what this stuff looks like IN the case, hehe....
|
|
|
|
|
08-12-2008, 09:47 PM
|
#24 |
|
Member (6 bit)
Join Date: Mar 2008
Posts: 55
|
hey mr. shadow, any idea how to make my screen a little smaller. it was working fine to begin with but now i can't see the outside of all sides. barely see the start bar on the bottom of my desktop and can't see the top of all pages like where you minimize or X of a screen. i tried messing with my res with no success. thanks...
|
|
|
|
|
08-12-2008, 09:49 PM
|
#25 |
|
I like me
Join Date: May 2007
Location: Tejas
Posts: 7,332
|
Two things: What size monitor, and what resolution do you have it at? Set it at it's max.
Second thing is: Try the buttons on the monitor. They should have either a refresh, an dadjust, or a setting that will help you shrink the screen as well as center it. |
|
|
|
|
08-12-2008, 09:59 PM
|
#26 |
|
Member (6 bit)
Join Date: Mar 2008
Posts: 55
|
it's a 32" hdtv. it was showing the whole screen just a little while ago. i dl a few things such as the latest vid card driver.
|
|
|
|
|
08-12-2008, 10:04 PM
|
#27 |
|
I like me
Join Date: May 2007
Location: Tejas
Posts: 7,332
|
The correct and newest drivers should help.
I have no idea what the resolution would be though for view on a 32" tv. Someone else might have to chime in on that. |
|
|
|
|
08-13-2008, 10:09 AM
|
#28 |
|
Member (6 bit)
Join Date: Jul 2008
Posts: 46
|
I think mine's 1366x768. Probably varies by brand. I'd just google ' "your TV's product id" maximum resolution'
It sounds like you hit the Ratio button on your tv remote, though (switched it to one of the Zoom modes). |
|
|
|
|
08-14-2008, 03:48 AM
|
#29 |
|
Member (6 bit)
Join Date: Mar 2008
Posts: 55
|
thank you guys. i found it. just went with all the different resolutions until i got the best one. thanks for all the help...
|
|
|
|
|
| Bookmarks |
| Thread Tools | Search this Thread |
| Display Modes | Rate This Thread |
|
|
Linear Mode
