|
|||||||
 |
|
|
LinkBack | Thread Tools | Search this Thread | Rate Thread | Display Modes |
05-16-2010, 09:24 AM
|
#1 |
|
Member (4 bit)
Join Date: May 2010
Posts: 9
|
New i5 build questions
Greetings, I have questions about the intel desktop board dp55kg quick reference step 18, 19, and 20.
Step 18 What do you do/? What is a Chassis Intrusion? Do you flip a switch? Step 19 It looks like you ground something to the green "board" on the mobo. Is that correct? If so, what do you connect? Step 20 BIOS Configuration Jumper Block I'm not sure what the instructions are telling me to do. I tried skipping these steps and booting up but the computer starts, I get no signal from the monitor. Then after a couple of codes flashing (4F, 27, 60) the computer shuts down then restarts. After a while it just rests on 4F. Any assistance is much appreciated. |
|
|
|
05-16-2010, 10:07 AM
|
#2 |
|
Forum Administrator
Staff
Premium Member
Join Date: May 2000
Location: Joplin MO
Posts: 37,767
|
|
|
|
|
|
05-16-2010, 11:09 AM
|
#3 |
|
Member (4 bit)
Join Date: May 2010
Posts: 9
|
I've taken everything out and "bench tested" the system. It still does the same sequence described above. Because I ordered the CPU and mobo from bestbuy, I don't think that I'll have a problem exchanging them, but before I do that I'm wondering if anyone knows what these steps shown in the instructions are. I'm sure they're important.
|
|
|
|
|
05-16-2010, 01:24 PM
|
#4 |
|
Forum Administrator
Staff
Premium Member
Join Date: May 2000
Location: Joplin MO
Posts: 37,767
|
Which exact processor do you have?
I do not believe you have to do anything with those 3 steps. Without a link to these instructions, I can't verify that. |
|
|
|
|
05-16-2010, 03:18 PM
|
#5 |
|
Member (4 bit)
Join Date: May 2010
Posts: 9
|
Intel DP55KG board
i5 661 processor After the rebuild, I now get status codes 31 and 26 from the mobo. I wonder if this is the correct RAM (PC3-12800). |
|
|
|
|
05-16-2010, 04:48 PM
|
#6 |
|
Member (9 bit)
Join Date: May 2009
Location: 127.0.0.1
Posts: 357
|
What brand and model of the memory? 12800 is not specific enough.
__________________
My Rig: Q9550 | Freezer 7 Pro (rev. 2) | EVGA GTX 560 Ti | OCZ 4GB DDR2 PC6400 | Gigabyte G31M-ES2L (v1.1) | 650W Corsair (CMPSU-650HX) | 500GB WD Caviar Black | NZXT Phantom White | Windows 7 Home Premium 64-bit DXeleven F@H |
|
|
|
|
05-16-2010, 05:07 PM
|
#7 |
|
Member (4 bit)
Join Date: May 2010
Posts: 9
|
First I tried
Corsair 1600 MHz 4GB then I switched to PNY DDR 3 PCS-10666. 1333 MHz compatible I'm now getting codes that say I need to update the BIOS with an external computer. Has anyone had this happen before? |
|
|
|
|
05-16-2010, 10:03 PM
|
#8 |
|
Forum Administrator
Staff
Premium Member
Join Date: May 2000
Location: Joplin MO
Posts: 37,767
|
Bios 4905 is required to support that processor. The board probably shipped with an older bios.
http://downloadcenter.intel.com/Deta...18887&lang=eng |
|
|
|
|
05-18-2010, 04:31 PM
|
#9 |
|
Member (4 bit)
Join Date: May 2010
Posts: 9
|
Thanks!!!
I can't believe it. It actually worked. Thanks so much.
Don't forget to reinstall in jumper pin! |
|
|
|
|
| Bookmarks |
| Thread Tools | Search this Thread |
| Display Modes | Rate This Thread |
|
|
Linear Mode
