Go Back   PCMech Forums > Help & Discussion > Computer Hardware

Need Some Help? Type Your Keywords Here:

Reply
 
LinkBack Thread Tools Search this Thread Rate Thread Display Modes
Old 01-25-2008, 12:55 PM   #1
Member (4 bit)
 
Join Date: Jan 2008
Posts: 14
Can i put a fan in my case?

I have a really old computer case without any fan. There are holes in the back though. I"m thinking of putting a fan on the side. How do I manage to do that and how do i cut a hole on the side?
inmate85 is offline   Reply With Quote
Old 01-25-2008, 01:09 PM   #2
 
hitchface's Avatar
 
Join Date: Dec 2006
Location: Alberta, Canada
Posts: 1,382
Pick your fan size, purchase it, and do your measurements as to where you want it to be. Cut a hole (with a dremel or similar) so that the outer edges of the fan will make contact with the case. From there you can punch holes where the screws will go. Make sure the holes are smaller than the screw size. You might want to drill the hole if the case is plastic or a little flimsy.

If you just want one fan, stick it in the back, where the mount has already been made. It should be all you need for some basic cooling.
__________________
TFH, paraphrased:

the bultin brner wouldnt evn boot it a usb burner woud but ten it gaeve an eror after i typed teh prduct key. i dont no waht it was it was a missng file, i fergt waht ti was but ti loked imporant can any1 help PLZ?!

Check out PCP! (that's PCProfiles in case you thought I was on angel dust) http://www.pcprofiles.com/p/hitchface
hitchface is offline   Reply With Quote
Old 01-25-2008, 01:23 PM   #3
Shiro Usagi
Premium Member
 
Cricket's Avatar
 
Join Date: Sep 1999
Location: Kaneohe, Hawaii
Posts: 34,002
Here's a "How-To" guide.

Cricket
Cricket is offline   Reply With Quote
Old 01-25-2008, 01:26 PM   #4
Member (4 bit)
 
Join Date: Jan 2008
Posts: 14
now that u mentioned it, i do see a mounting for a fan in the back. thank you so much. Now i probably have to measure it and buy the right size.
inmate85 is offline   Reply With Quote
Old 01-25-2008, 01:30 PM   #5
 
hitchface's Avatar
 
Join Date: Dec 2006
Location: Alberta, Canada
Posts: 1,382
The standard size on older cases is 80mm. But measure anyways.
hitchface is offline   Reply With Quote
Old 01-25-2008, 01:43 PM   #6
Member (4 bit)
 
Join Date: Jan 2008
Posts: 14
another question i want to ask is where are the 3 pin connectors? I noe that there is one close to the cpu for the cpu fan. You probably need to have a motherboard has a lot of them huh?

On my mobo, there is a 3 pin connector close to cpu and i think one close to the south bridge.
I"m thinking about this one

http://www.newegg.com/Product/ShowIm...5S1M4+Case+Fan

Last edited by inmate85; 01-25-2008 at 01:45 PM.
inmate85 is offline   Reply With Quote
Old 01-25-2008, 01:55 PM   #7
Shiro Usagi
Premium Member
 
Cricket's Avatar
 
Join Date: Sep 1999
Location: Kaneohe, Hawaii
Posts: 34,002
It's better to connect case fans directly to the power supply instead of the motherboard. You reduce the load on the motherboard power circuit this way...helps with system stability.

Cricket
Cricket is offline   Reply With Quote
Old 01-25-2008, 02:50 PM   #8
Member (7 bit)
 
brizey's Avatar
 
Join Date: Oct 2005
Location: Dallas, TX Metro Area
Posts: 79
Quote:
Originally Posted by Cricket
It's better to connect case fans directly to the power supply instead of the motherboard. You reduce the load on the motherboard power circuit this way...helps with system stability.

Cricket
...especially with a external case fan. Pretty easy to tell if it is still working. I use the mother board to monitor my intake fan since I can't see it (Sonata II case--it is behind the hard drive bay). It is still powered by the PSU, only a monitor line is attached to the MB.
brizey is offline   Reply With Quote
Old 01-25-2008, 04:54 PM   #9
Member (4 bit)
 
Join Date: Jan 2008
Posts: 14
i do want a side fan...is there anything to protect the fan so external stuff fly into and ruin the fan?
inmate85 is offline   Reply With Quote
Old 01-25-2008, 05:02 PM   #10
Shiro Usagi
Premium Member
 
Cricket's Avatar
 
Join Date: Sep 1999
Location: Kaneohe, Hawaii
Posts: 34,002
You can either put a wire grill or a screen filter over the opening. You can find these at most on-line vendors that sell cooling fans.

Cricket
Cricket is offline   Reply With Quote
Old 01-25-2008, 09:06 PM   #11
Techphile.
 
David M's Avatar
 
Join Date: Nov 2003
Location: San Francisco Bay
Posts: 5,746
The filters used for fish tanks work well...you just cut it to size and wash it occasionally
__________________
Asus P8P67 WS Revolution | Intel 2600K @ 4.7 GHz | Win 7 Pro 64 |8 gigs Corsair 1600 | Two Diamond 6990's in Crossfire| Corsair AX1200 | Thermalright Silver Arrow | Western Digital Black 2TB 64 meg cache | Lian-Li PC-A71B | Logitec Z-5500 | Three Asus 26" VW266H monitors running under Eyefinity |
David M is offline   Reply With Quote
Reply

Bookmarks

Still Need Help? Type Your Keywords Here:


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Want to install additional Case fan cdplayer Computer Hardware 4 06-18-2005 08:16 AM
Aspire X-Navigator Case Fan Air Flow Direction Question. cc6000 Computer Hardware 2 01-24-2005 07:18 PM
Cooling Fans Setup Fowlerflap Computer Hardware 18 08-13-2003 04:59 AM
Something wrong wit case temps. phatboi Computer Hardware 23 05-21-2002 08:10 AM


All times are GMT -5. The time now is 10:59 PM.
Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2012, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.6.0