|
|||||||
 |
|
|
LinkBack | Thread Tools | Search this Thread | Rate Thread | Display Modes |
09-10-2002, 08:06 PM
|
#1 |
|
Member (9 bit)
Join Date: Jun 2001
Location: Maine
Posts: 310
|
scandisk not working
I have been having problems recently with my computer, such as hangups on shutdown. So, I went through and fdisked and formatted the hard drives to get a clean install. Had to do this twice, but finally took. I reloaded all the latest from microsoft, followed by the new drivers. Now it will not run scandisk when selected. It just locks up and I have to manually shut the computer down. It will run scandisc on it's own for improper shutdown, however. Defrag works fine.
Any ideas? |
|
|
|
09-11-2002, 04:14 AM
|
#2 |
|
Member (8 bit)
Join Date: Jan 2002
Posts: 146
  |
try running scandisk through MS-Dos then try it again through windows when the MS-Dos is finished
|
|
|
|
|
09-11-2002, 09:46 AM
|
#3 |
|
Shiro Usagi
Premium Member
Join Date: Sep 1999
Location: Kaneohe, Hawaii
Posts: 34,002
|
Hi hoemee,
Seems you're having hardware problems of some sort. Since you're using IBM hard drives, I would download the hard drive diagnostic utilities and test your drives out. You might also want to replace the rounded IDE cables with regular ribbon cables...I understand you can get data corruption with rounded cables. Problem could be related to RAM. I'm not sure if DocMemory will test RAMBUS but you could try.  Cricket
|
|
|
|
|
09-11-2002, 10:16 AM
|
#4 |
|
Member (9 bit)
Join Date: Jun 2001
Location: Maine
Posts: 310
|
Thanks for the replies. I cannot get into MSDOS mode to run scandisc that way. I suspected a hardware problem as well. I have two 40 gig hdd running in the raid mirror config. Since I built this machine, the second(hidden) hard drive runs at ultra dma 2 mode, while the primary one runs at udma 5 mode. I downloaded the utility from IBM and verified they were both set to UDMA 5 mode. I will try the download from IBM to test the drives and go from there. I check docmemory tester as well.
I'll keep you posted. hoemee |
|
|
|
|
09-11-2002, 11:53 AM
|
#5 |
|
Member (9 bit)
Join Date: Jun 2001
Location: Maine
Posts: 310
|
Just ran the docmemory tests - both the quick and burn in. All tests passed.
|
|
|
|
|
09-14-2002, 03:53 PM
|
#6 |
|
Member (9 bit)
Join Date: Jun 2001
Location: Maine
Posts: 310
|
Well, I tried to run windows setup and it just locked up - had to format and reload. Scandick is working fine now and I am reloading all drivers. We'll see how it goes. If I have any more problems I'll post them.
thanks, hoemee |
|
|
|
|
09-16-2002, 06:33 PM
|
#7 |
|
Member (9 bit)
Join Date: Jun 2001
Location: Maine
Posts: 310
|
This is the only intermittent problem I am having now...after I turn on my computer and let it boot I select the explorer icon on my task bar in the lower left hand corner. This will prompt my dial up connection window to display. Then my computer shuts down and reboots, running scandisk - with no errors found.
hoemee |
|
|
|
|
09-16-2002, 07:34 PM
|
#8 |
|
Member (10 bit)
Premium Member
Join Date: Jul 1999
Location: Fairfax, Va
Posts: 998
|
sounds like something is heating up. Is there HS compound and a fan on the CPU?
__________________
After 40, its a matter of maintenance |
|
|
|
|
09-17-2002, 04:48 AM
|
#9 |
|
Member (9 bit)
Join Date: Jun 2001
Location: Maine
Posts: 310
|
I just went with what was on there when I bought it - the oem stuff. I do have a tube of arctic silver though.
|
|
|
|
|
09-17-2002, 06:08 AM
|
#10 |
|
Member (10 bit)
Premium Member
Join Date: Jul 1999
Location: Fairfax, Va
Posts: 998
|
Do it. Apply a thin and even film, reseat and try it.
|
|
|
|
|
| Bookmarks |
| Thread Tools | Search this Thread |
| Display Modes | Rate This Thread |
|
|
Linear Mode
